Description
CIRCUIT BOARD DEFECT? WHAT SHOULD YOU DO?
Is it a washing machine or a tumble dryer? Read on below. If it’s a dishwasher, read more via dishwasher
This Bauknecht Whirlpool circuit board servicing is intended for washing machines and tumble dryers that are completely dead and no indicator light at all comes on.
1. Disassemble the circuit board behind the large round control knob (the circuit board is located in a plastic cassette). So it’s not about any smaller circuit board that may be present, on which the time is displayed.
2. Send the defective circuit board, with or without the grey cassette, well packaged to Euromaxx in Wijchen. See the contact details.
5. On the day the circuit board arrives with us, we typically send it back repaired. You will then receive a track & trace number in your email inbox. In exceptional cases we need to order parts and it will take longer, but that is rare.
GENERAL:
We service circuit boards from virtually all major appliance brands, including WHIRLPOOL, BAUKNECHT, AEG, ELECTROLUX, ZANUSSI, MIELE, BOSCH, SIEMENS, SAMSUNG and LG, for washing machines, tumble dryers, dishwashers, cooker hoods, etc.
The fault is as follows: the appliance is completely dead, no indicator light comes on at all, and the machine does nothing.
The cause is often that ICs are mounted on the circuit board that are too light for the power draw of multiple relays.
In most cases, some components on the circuit board are defective. We replace these components and install, as a precaution, heavier versions.
You could consider a new circuit board, but it often contains the same too-light components again, which can cause malfunctions. In addition, new circuit boards are much more expensive. A second-hand circuit board may contain the same weak components.
TESTING:
If the circuit board is completely dead, there is almost a 100% chance that the fault is in the circuit board. Measuring and testing usually therefore makes little sense.
If you still want 100% certainty, you can check whether 220 volts are present on the white connector plug that is located exactly in the middle on the back of the circuit board and has three small angled contacts and two wires. If there is 220 V present, the circuit board is defective. You don’t have to measure it yourself: if the circuit board is fine, we will see that and inform you immediately. We also don’t charge any servicing costs.
Please note that measuring while powered is not work for laypeople. Only work with electricity if you, or someone who does this for you, has more than sufficient experience with this kind of measurement. If you’re unsure, then definitely don’t do it!
WHAT DO WE DO?
You send us your old defective circuit board and we repair it. We replace the defective and too-light components and fit the correct, heavier components onto the board. After that, we test and reprogram the circuit board and send it back, usually on the same day we receive your circuit board. You can tell the board is on its way once you receive a track & trace number in your email inbox.
DISASSEMBLY:
- Unplug the power cord from the wall outlet
- Remove the top cover by loosening the two screws on the rear side
- Loosen the two screws that are located at the top in the control panel and become visible after removal of the top cover.
- Remove the detergent drawer by sliding it forward and pressing down the white, lip-shaped plastic clip at the back while you pull the detergent drawer forward.
- Remove the 3 small screws (size 5.5 mm) that are now visible.
- When you are standing in front of the appliance, behind the front panel on the inside on the right there is a plastic clip. Move it aside with your hand so that the front comes loose. Then remove the front; it will remain attached to the wiring.
- Take photos or a video of the wiring for later reassembly and disconnect all wires
- The panel is now detached from the washing machine
- Place the panel on the selector switch knob, which is in position 0. Using a flat-head screwdriver, you can now remove the circuit board with its plastic holder from the rear. The knob stays attached to the panel, untouched.
- Send the complete panel. Leave the grey cassette around the circuit board in place.
Do you need more detailed instructions? Then indicate this in the comments box at the end of your order.
CONDITIONS AND WARRANTY
We assume a fault in the module’s power supply, which we repair. You can tell the repair has been carried out because the indicator lights on the circuit board come on again. We provide a 3-month warranty, during which you are responsible for supplying the module. Warranty does not apply if malfunctions in the machine itself are the cause. In rare cases, the failure of this circuit board can be caused by another fault in the machine, or after repairing the circuit board it turns out that another fault is still present. This may even have been responsible for the circuit board failing again, even directly after reconnecting following the repair.
In a single case, the switch may also have become defective. Switches are excluded from repair, partly because they are no longer available.
You are responsible for proper packaging of the circuit board. We are not liable for transport damage. For environmental reasons, we use your packaging for the return shipment.
If your circuit board is damaged beyond repair, we will not carry out the repair and you do not have to pay the servicing costs. Only when we have to return the circuit board that can no longer be repaired, € 14.80 in handling and shipping costs will be deducted from the amount to be credited.
FACEBOOK:
Also check our Facebook page to read reviews from our customers!
https://www.facebook.com/pages/EUROMAXX/403606269786891
Success. If you have any questions, feel free to email or call us—also for help with removing and installing the part.
It concerns virtually ALL models both washing machines and tumble dryers such as MODEL ATLANTA, AWO, MIAMI, DENVER, BOSTON, CENTO, INDIANA, MEMPHIS, TEXAS, CHAMP, AWO, GREEN, etc. and for both 1200, 1400 and 1600 rpm.




