Description
Replacing Bosch washing machine drum bearings is a comprehensive repair in which the entire drum must be removed from the appliance. The bearings are located at the back of the drum. If they are worn, the washing machine will make a lot of noise and play may develop in the drum. Check this by moving the drum at the front. If it has a lot of play, the bearings are probably worn. In this repair, you should always also replace the Simmering or sealing ring. (picture 1) For the model in this example, the seal between the tub halves must also be replaced. The rear tub half is in fact detached from the front, which causes this seal to come loose. To order the correct parts, you need the full type number of the washing machine. This is usually found in the door opening or on the edge of the door. Set aside enough time for this repair. It’s a big job, but it can save you a lot of money. Before you start, always unplug the machine. In this example, we use a Bosch washing machine. Details may vary from appliance to appliance, but the overall method is virtually the same. Start by removing the top panel. This is secured with a few screws at the back of the machine. Often you need a Torx screwdriver or bit for this. Next, remove the detergent drawer by pressing in the clip, see picture 2. Then loosen the specified screws in picture 3 to remove the control panel. Keep the screws neatly organized so that you can put the different parts back in later more easily. You don’t need to completely disconnect the wiring. Carefully place the control panel on top of the machine. Now remove the plinth; this usually comes off easily. Also disconnect the drain hose. The front panel is secured with four screws, one in each corner. The manchet is still fixed with a clamp ring, which can differ per appliance. In this example, you remove it by carefully sliding a flat-head screwdriver under the ring and pulling the ring off. (picture 4) Then push the manchet inward. Now loosen the two screws at the door lock (picture 5), after which you can carefully lift the front panel off the machine. Under the detergent drawer housing there is a middle strut. You can remove it by turning it slightly upward, see picture 6. Then pull the detergent drawer housing backward. It is still attached to the drum with a hose. Move the housing as far back as possible so that you can reach the clamp (picture 7). Release the clamp using a pair of flat pliers. The detergent drawer housing is now detached from the drum and can, just like the front panel, rest on top of the machine. Now comes the hardest part: the counterweights. These also need to be removed. Under the drum there is the heating element. First take a photo of the wiring with a camera or mobile phone before you disconnect it. This way you can reconnect the wiring later in the same way. (picture 8) To remove the element, loosen the bolt in the middle. Do not remove it completely; leave it in place with a few turns on the wire. (picture 9) Then tap the bolt inward, for example with the back of a screwdriver. (picture 10) This releases the seal so you can remove the element easily. Under the drum there is also a hose, see picture 11. Before disconnecting it, drain as much water as possible through the drain hose at the front, as discussed earlier with the plinth. There may still be some water coming out of the drum even after draining. Therefore, keep a few towels nearby. The clamp of this hose is secured with one screw. The last part at the front is the drum wiring, see picture 12. Then continue at the back. Remove the rear panel. Next, remove the belt from the belt pulley by pulling the belt slightly toward you and at the same time turning the pulley. Be careful with your fingers. (picture 13) Then remove the motor, because it is also attached to the drum. First take a photo of the wiring before you disconnect it, so you can connect everything correctly later. The motor is secured at the front with two bolts. (picture 14) Once the bolts are loose, carefully pull the motor forward; it is fairly heavy. Also remove the pressure chamber on the side of the drum. This is secured with a plastic clip. (picture 15) Everything around the drum is now removed. The drum is only still hanging on the suspension springs and shock absorbers. First remove the shock absorbers. How you detach them depends on your machine. On some models it’s easier to detach the damper from the drum, while on other models it’s easier to detach it from the bottom of the machine. Assess on site which method works best. After that, the drum only remains attached to the springs and you can lift it out of the machine. Next, remove the manchet from the drum. It is still secured with a tension spring. Carefully slide a flat-head screwdriver under the spring and pull it loose. Avoid damaging the manchet. After that, you can remove the manchet. Place the drum on the front so that you can reach the belt pulley. Ideally place the drum on a few beams to prevent damage to the drum housing. (picture 16) The plastic belt pulley is secured with a bolt. Loosen it by, for example, placing the back of a hammer between the belt pulley, see picture 17. You will feel the drum sink inward. If the bearings are completely worn, you may need to tap the shaft further inward with a hammer to loosen the bearings. Now the tub halves must be separated. In picture 18 you can see that this tub is screwed together and also secured around with plastic clamps. This is not the case on all models. If your machine has these clamps, you can remove them with a sharp chisel. When installing the new sealing ring, screwing it in place is sufficient. First remove the plastic clamps and then loosen the screws. Separate the tub halves: first the front, and then pull the drum out of the rear tub half. In picture 19 you can see how the bearings and sealing are fitted in the machine. Remove the old bearings from the tub using a chisel, see picture 20. Move the chisel little by little and tap carefully so that the bearing comes loose evenly. Then turn the drum around and repeat this for the front bearing. The sealing ring normally comes off together with the bearing. First clean the seat of the new bearings thoroughly with a dry cloth. Dirt in this area can damage the new bearings. First fit the bearing on the inside of the tub half. Tap it into place very carefully and touch only the outer edge of the bearing. See picture 21. The bearing can be easily damaged if you strike the inner ring. Then install the sealing ring and tap it into place with a rubber mallet. (picture 22) The sealing ring must be flush with the edge of the tub half. Then mount the bearing on the outside of the tub in the same way. Also clean the shaft of the drum before putting the drum back in place. If the shaft is damaged, you may be able to replace it if the required parts are available. Start by refitting the drum into the rear tub half. Attach the belt pulley to the shaft. Then place the seal between the tub halves. The attachment point of the seal must be at the top of the drum. See picture 23. Press the seal firmly into the groove along the tub. In this example, an additional layer of silicone sealant is applied, and then the other tub half is put back in place. On some machines, the screw holes are numbered so that you know exactly in which order to install the screws. If that isn’t the case, position the screws opposite each other each time. If you want to check whether the tub is properly watertight, first wait until the sealant has completely dried. Then fill the tub with water to a little above halfway to check for leaks. If everything is in order, you can fully reassemble the washing machine again.




