Description
When your Siemens dishwasher keeps draining, this often points to an E15 fault: the tap light stays on and there may be a leak on the base plate.
In many Bosch, Siemens and Neff dishwashers, the drain pump keeps running even with the door open. Therefore, pull the plug from the socket right away; otherwise the pump keeps running unnecessarily and may fail.
This fault where your Siemens dishwasher keeps draining can have two causes: there is actually water on the base plate due to a leak or the dishwasher incorrectly detects a leak.
WHAT SHOULD YOU DO?
- First, pull the plug from the socket. Safety comes first.
- In a built-in dishwasher, loosen the lower metal kick plate of about 10 cm high at the front. This is usually secured with 2 or 4 Torx screws.
- Sometimes you also need to remove the green insulation cover.
- Use a lamp or carefully feel with your hand to check whether there is water on the base plate.
- Is there water on the base plate? Then continue reading. Is the base plate dry? Then continue at the bottom under “DRY E15”.
On many forums you read that you can simply remove the water from the bottom using toilet paper or a cloth, and that the dishwasher works again afterwards.
Of course, that is not a solution, because the leak is still there.
In addition, the earth-leakage circuit breaker may trip later. Therefore, do not take unnecessary risks and fix the cause of the leak.
HOW DO YOU SEAL THE LEAK?
So the leak must first be properly repaired.
The base plate is often made of stainless steel, and the pump well underneath is made of plastic. These materials expand differently, which can cause the seal to start leaking.
For this, a special servicing repair kit is available.
You carry out this repair from inside, so you do not need to pull the appliance out or dismantle it. Below you can see the pump well whose rim usually leaks.
When you order, you receive a complete set with servicing kit and special sealing compound.
The package is sent as a small box and unfortunately does not fit through the letterbox.
The set is in stock and can be shipped today.
ATTENTION: both Siemens and Bosch’s service department’s and our workshop always use a special sealing compound during installation.
This compound is resistant to dishwasher tablets, salt and rinse aid, in combination with high and varying temperatures.
This special compound is included in the package. Below you can see what is supplied:
KIT 1
- Everything stays in place, including the thick original black ring.
- First remove the 4 old screws and let the pump well drop down. Dry everything thoroughly with a cloth and a hairdryer.
- Mount the new, thinner ring. Just place it onto the existing ring.
- Then apply plenty of compound and use the tube almost completely. Especially at the back this is difficult; if you use too little compound there, the leak may return.
- Then mount the new screws. Since you screw them into plastic, do not tighten them too much.
- Remove excess compound.
- Let the compound dry for 24 hours. After that, the repair is complete.
Want to see how to perform this servicing? Then watch this video.
Note: in this video no compound is applied, but it needs to be applied. Watch the instruction video on YouTube
Note: do not pull the ring too hard when replacing it. No warranty applies to a torn ring.
The ring may look split on delivery in the box. This is normal and not transport damage.
So do not order a new set if you see this.
The rim of this base plate can sometimes be razor-sharp. Watch your fingers and also prevent damage to the ring.
EXCEPTION:
There is one exception to the Bosch Siemens E15 fault: the Zeolith models. You can recognize this when you open the dishwasher door; inside the stainless steel you will then see ZEOLITH in large letters.
In that case, you also need to seal the rim of this container with compound. For this, the Zeolith boiler must be lowered. On the base plate you can see a stainless-steel bulge at the back right; this must be disassembled.
This covers the most common causes of the E15 fault.
With a dry E15 fault, there are 2 variants:
VARIATION 1: SIEMENS dishwasher keeps draining
- You have an E15 or tap fault, but there is no water on the lower base plate.
- This fault occurs almost only with a plastic base plate, not with stainless steel. In that case, the drain pump is often defective, sometimes in combination with dirt or blockage in the pump section.
- What should you do? Order a new drain pump and find your model at drain pump for Bosch dishwasher
VARIATION 2: SIEMENS dishwasher keeps draining
- There is another possibility with a dry E15: the tap light stays on, but the dishwasher does not keep draining and simply stops during the program.
- Then not enough water enters, or it does not enter quickly enough. The inlet valve on the side of the appliance, at the bottom of the labyrinth, may be defective.
- Start the appliance and check whether at any point water enters and the entire labyrinth empties.
- If that is not the case, order a new inlet valve: FAULT E19 BOSCH SIEMENS dishwasher ATAG NEFF CONSTRUCTA
- If there is still a rare cause after that, there may be a blockage in the cream-colored hose that runs from the pump well to the water heat exchanger.
RETURNS
Do you want to return this article? That is only possible in unopened packaging, in new condition and as a complete set. Separate parts of the set cannot be returned.
We will also deduct the shipping costs we incur from you.















Reviews
There are no reviews yet.